[ Pacific Security Network News ]
For the family, the importance of the floor is unquestionable. This article introduces you to the common faults and treatment methods of the floor.
First, the seam starts to drum
A. Water in the surface of the floor: During the installation process, it is inevitable that the glue does not completely fill the seam. If the drip of the mop will cause water on the surface of the floor and enter from the seam with less sizing, the floor substrate will absorb water, causing local expansion and blistering. In this case, the surface of the floor surface is partially bulged;
B. Under the floor, the water enters the drum: the surface phenomenon is that the shape of the joint is more uniform, the place near the water source is heavier, and the far place is more and more flat. Somewhere with such problems are: close to the bathroom, kitchen, heating pipes, air conditioning condensate drains, windows, etc. If the water immersion time is long and the surface phenomenon is not obvious, the floor can be opened to check whether there is a watermark to determine the cause;
C. Short seams on the floor: It is expressed as a long floor. Each short side seam is a drum, which is usually caused by too much moisture on the ground. The higher the bulge, the greater the tidal moisture on the ground.
Maintenance plan: Replace the floor.
Second, the floor arch
The performance phenomenon is that there is a sense of suspension when stepping on, and some places will be more serious.
A. The expansion joint is not reserved enough to make the floor arch;
B. Room-wide shop: Two or more rooms are not equipped with buckles when installing the floor. When the moisture and moisture are large, the two rooms floor are stretched laterally, causing the door to be involved in each other to make the floor arch;
C. The expansion joint is nailed by the baseboard or filled with plaster, putty, etc., so that the floor cannot be stretched, resulting in the arching of the floor;
D. During the installation process, foreign objects remain under the floor, causing arching;
E. The base layer under the floor is arched. If the original floor has a solid wood floor before the floor is installed, the original floor is damp and arched after the floor is installed, causing the floor to be arched;
Maintenance plan: start the skirting board, reserve the expansion joint again; install the buckle at the connection between the room and the room; re-install the baseboard, clean out the expansion joints such as plaster and putty; open the floor and refill; The floor is dropped, the floor is leveled, and the floor is re-paved after drying.
Third, the floor crack
A. The ground is uneven: the floor is paved under the condition that the ground is uneven, and after a period of use, the glue between the floors is separated to create a gap;
B. Less glue: the floor is in the winter, there is heating and baking, the air is dry, the floor is flat, the joint glue is insufficient, the strength is not enough, and the floor is opened and the seam is cracked;
C. There are heavy objects on the opposite side: the parallel opposite direction of the floor to be repaired is pressed by heavy objects, so that the floor cannot be freely contracted and cracks occur; such a room will be arched in the summer, and cracks will occur in the winter when the heating comes. phenomenon;
Maintenance plan: remove the floor, the floor is leveled, dry and re-paved; according to the size of the crack, decide to add wax, refill; use special tools to fix or reload; remove heavy objects, refill and fix.
Fourth, surface defects
A. Falling angle: The floor bumps during the handling process. The construction personnel do not pay attention to it during the construction process or shovel when cleaning the glue after the construction, so that the corners of the floor have a corner drop phenomenon;
B. Surface peeling: After construction, sharp objects or heavy objects fall off the floor, which affects the appearance of the floor; or the surface layer and the substrate are not glued during the processing of the floor, after a period of use, the surface layer and the substrate are degummed;
C. Scratches: When the customer puts furniture or heavy objects on the floor, the floor and the items are mixed with nails or sand, etc., and the floor wear layer is damaged or the scratches are obvious;
Maintenance plan: wax block repair or replacement of the floor.
Fifth, the floor stains:
The floor is stained on a large area and difficult to clean.
A. Due to the floor structure, the stains that cannot be cleaned are caused;
B, the floor performance is not good, the stain can not be cleaned after infiltration, resulting in black spots or black lines on the surface;
Maintenance plan: Use a professional brush to clean the floor and take the correct maintenance method; if it is a quality problem, replace the problematic floor.
Six, the skirting board problem
A. Arching: Due to the wet weather or wet wall, the kicking foot has no expansion and expansion space;
B. The interface is not flat: the height of the interface is not uniform due to uneven ground or improper installation;
C. There is a gap between the wall surface, the cabinet and other façades: the wall is not flat or the nail layout is unreasonable;
D. There is a gap with the ground: mainly due to uneven ground;
Maintenance plan: Start the skirting board, re-install the installation, make up the putty and so on.

1. Technical standard: BS EN 10202, DIN EN 10203, GB/T2520 , JIS G3303
2. Steel type: MR, SPCC
3. Thickness: 0.115 - 0.50 mm
4. Roll width:  600 - 1050 mm
Tin Coating: ordinary 2.8 or 2.8g and 5.6g or 5.6g, we can produce according to customer's requests
Widely apply to industrial packagings and food packagings.

Electrolytic Tinplate Coil

Electrolytic Tinplate Coil,Coil With Color Printing,Electrolytic Tinplate,Electrolytic Tinplate Sheet In Coil

Jiangsu Guolian New Material Co., Ltd. , https://www.cntinplate.com